The Effect of Sodium Dodecyl Benzene Sulfonate on Particle Size in Suspension Polymerization of Styrene: A New Investigation

It is well known that inorganic solids can be used for droplet stabilization in suspension polymerization. This work investigates the effect of tricalcium phosphate (TCP) as an inorganic stabilizer and sodium dodecyl benzene sulfonate (SDBS) as a surface active agent for suspension polymerization of styrene. The results show that when large amounts of TCP is used, the amount of SDBS has no effect on particle size. The effect of concentration of SDBS will be very important if a small amount of TCP is used. Scanning electron microscopy analysis shows that TCP is adsorbed on the surface of monomer droplets and also the coalescence factor changes with concentration of SDBS in the solution.     

Effect of fluoride varnish with added casein phosphopeptide-amorphous calcium phosphate on bond strength to enamel

To investigate the effect of fluoride varnish with added casein phosphopeptide-amorphous calcium phosphate on the shear bond strength (SBS) of two adhesive systems to enamel. Specimens obtained from permanent teeth were randomly distributed among four groups for enamel pretreatment [Control (no treatment, CNT), Duraphat varnish (DV), Clinpro White varnish (CWV), MI Varnish (MIV)], and each group was further divided into two subgroups according to adhesive [Etch&rinse (Adper Single Bond, ASB), self-etch (Clearfil SE Bond, CSE)]. Specimens were stored in distilled water at 37 °C for 24 h. Cylindrical composite specimens (2.3 mm in diameter, 3.0 mm in height) were then bonded to the enamel surfaces. SBS tests were performed and data were analyzed with two-way ANOVA and Tukey’s tests. For both CSE and ASB, SBS values of the CNT groups were significantly higher than those of all the enamel pretreatment groups (p < 0.05). Among the enamel pretreatment groups, SBS values with both adhesive systems were lowest in the MIV groups, followed by CWV and DV groups. In conclusion, pretreatment of enamel surfaces with fluoride-containing varnishes reduced bonding performance of adhesive systems to enamel. MIV appeared to cause greater enamel surface alterations and precipitation, which interfered with adhesive bonding mechanisms.     

制氢装置含机械损伤缺陷解吸气混合罐安全性分析

某制氢装置的一台解吸气混合罐,在检验过程中发现130mm长、2mm深的机械划痕,采用断裂力学方法对其开展了安全评价。根据断裂评价结果,该缺陷是可以接受的。     

Experimental investigation of hydrogen storage in capillary arrays

We present the results of the experimental investigation of hydrogen storage in glass capillary arrays. It is demonstrated that quartz–epoxy capillary arrays can have extremely high gravimetric and volumetric capacity, exceeding US DOE 2010 target values. The new method of pressurized hydrogen loading and releasing is developed based on plugging up the capillaries with stoppers in high-pressure environment.     

Parameters Influencing Third‐Phase Formation in the Extraction of Th(NO3)4 by some Trialkyl Phosphates

Third‐phase formation in the extraction of Th(IV) by trialkyl phosphates (TalP) such as tri‐n‐butyl phosphate (TBP), tri‐iso‐butyl phosphate (TiBP), tri‐sec‐butyl phosphate (TsBP), tri‐n‐amyl phosphate (TAP), tri‐2‐methylbutyl phosphate (T2MBP), tri‐iso‐amyl phosphate (TiAP), tri‐sec‐amyl phosphate (TsAP), and tri‐cyclo‐amyl phosphate (TcyAP) has been investigated under various conditions. Formation of a third phase in the extraction of Th(IV) by TBP/n‐dodecane as a function of TBP concentration at 303 K was studied. Measurements were also carried out on the extraction of Th(IV) from its solution with near‐zero free acidity by various phosphate/diluent binary solutions (1.1 M) as a function of temperature. Third‐phase formation in the extraction of Th(IV) by 1.1 M TalP in various diluents from nitric acid media has also been studied as a function of equilibrium aqueous‐phase acidity at 303 K. Empirical equations to predict limiting organic concentration with respect to various parameters for third‐phase formation in the extraction of Th(IV) by TBP and TAP from nitric acid media have been derived. Some of the above phosphates have been investigated for the distribution of Th(NO₃)₄ between the “diluent‐rich phase” (DP) and “third‐phase” (TP) in the extraction of Th(IV) by 1.1 M TalP in various diluents from its saturated solution with near‐zero free acidity at 303 K. Results of the above studies are presented in this paper. Based on these studies, the effects of extractant concentration, the temperature, the nature of the diluent, the equilibrium aqueous‐phase acidity, and the structure of the extractant on third‐phase formation behavior of trialkyl phosphates are described in this paper.     

Superfine Spherical Hollow Ammonium Dihydrogen Phosphate Fire-Extinguishing Particles Prepared by Spray Drying

Superfine spherical hollow ammonium dihydrogen phosphate fire-extinguishing particles are prepared by spray drying and modified in situ with silicon oil emulsion. The results show that the amount of rough particles increased observably when the proportion of silicon oil emulsion is increased from 9 to 15 wt%, while no significant difference is detected when the proportion of silicon oil emulsion was varied from 0 to 9 wt%. The flowability of particles is improved with an increase in the proportion of silicon oil emulsion; 9.0 wt% is the optimal proportion of silicon oil emulsion for improving the hydrophobic performance of particles. Fire-extinguishing tests show that the fire-extinguishing capability of spray-dried superfine spherical hollow ammonium dihydrogen phosphate fire-extinguishing particles is much better than the two varieties of existing superfine dry chemical fire-extinguishing agents.     

Influence of melt cleanliness on pore formation in aluminium—silicon alloys

Porosity and inclusions are the most serious problems encountered in the production of aluminium castings. The formation of porosity during solidification can be affected by several factors such as melt hydrogen, cooling rate, alloying elements, modification and melt cleanliness. Of all these factors, melt cleanliness (i.e. inclusion concentration) is the most difficult to control and is often considered as a key factor influencing the pore nucleation. In the present paper, the effect of melt cleanliness on porosity formation in two aluminium foundry alloys (A356 and 319) was investigated systematically. Melts with different inclusion levels were prepared and tested by the reduced pressure test, and the melt cleanliness was quantified using a pressure filtration technique. In addition, the influence of filtration by ceramic foam filters on the porosity was studied.

Results indicate that, at the same hydrogen level and with increased inclusion concentration, the density of reduced pressure samples decreases, and the amount of porosity and the number of pores increase. This trend is confirmed in both 356 and 319 alloys over a wide range of hydrogen levels. These results are discussed in the context of the nucleating effects of inclusions on pore formation during solidification. The practical application of the reduced pressure test for evaluation of both the melt cleanliness and the dissolved hydrogen level is outlined.     

Relaxation Properties of Pressure-sensitive Adhesives upon Withdrawal of Bonding Pressure

Relaxation properties of pressure-sensitive adhesives (PSA) have been studied with the squeeze-recoil tester used in the regime of parallel-plate dilatometer under conditions imitating the removal of compressive force in the course of adhesive bond formation. The relaxation properties of PSAs are compared with their adhesive behavior measured using the 180-Deg Peel Test. Two classes of PSAs are considered: 1) conventional rubbery adhesives based on the mixtures of styrene-isoprene-styrene (SIS) block copolymer with a tackifier resin and a plasticizer, and butyl rubber plasticized with low-molecular-weight polyisobutylene, and 2) hydrophilic PSAs composed of the blends of high-molecular-weight poly(N-vinyl pyrrolidone) (PVP) with oligomeric polyethylene glycol (PEG). By comparing the adhesive and relaxation behaviors of different PSAs, the relaxation criteria for pressure-sensitive adhesion have been stated. Relaxation behavior of the examined PSAs demonstrates two values of retardation time: the shorter retardation time of 10–70?sec and the longer time of 300–660?sec. These times can be associated, respectively, with small- and large-scale mechanisms of strain recovery. By comparing the relaxation and adhesive properties of PVP-PEG blend (which involves the formation of a hydrogen-bonded network through both terminal hydroxyl groups in PEG short chains) with the properties of covalently crosslinked copolymers of vinyl pyrrolidone (VP) with PEG-diacrylate and comb-like VP copolymers with PEG-monomethacrylate, the contributions of covalent crosslinking and H-bonding network have been characterized.     

In Vitro and in Vivo Characteristics of Fluorapatite-Forming Calcium Phosphate Cements

This study reports for the first time in vitro and in vivo properties of fluorapatite (FA)-forming calcium phosphate cements (CPCs). The experimental cements contained from (0 to 3.1) mass % of F, corresponding to presence of FA at levels of approximately (0 to 87) mass %. The crystallinity of the apatitic cement product increased greatly with the FA content. When implanted subcutaneously in rats, the in vivo resorption rate decreased significantly with increasing FA content. The cement with the highest FA content was not resorbed in soft tissue, making it the first known biocompatible and bioinert CPC. These bioinert CPCs might be useful for applications where slow or no resorption of the implant is required to achieve the desired clinical outcome.     

A Review of Fatigue Crack Growth for Pipeline Steels Exposed to Hydrogen

Hydrogen pipeline systems offer an economical means of storing and transporting energy in the form of hydrogen gas. Pipelines can be used to transport hydrogen that has been generated at solar and wind farms to and from salt cavern storage locations. In addition, pipeline transportation systems will be essential before widespread hydrogen fuel cell vehicle technology becomes a reality. Since hydrogen pipeline use is expected to grow, the mechanical integrity of these pipelines will need to be validated under the presence of pressurized hydrogen. This paper focuses on a review of the fatigue crack growth response of pipeline steels when exposed to gaseous hydrogen environments. Because of defect-tolerant design principles in pipeline structures, it is essential that designers consider hydrogen-assisted fatigue crack growth behavior in these applications.